Inactive on SAM.gov — responses were due 16 Sep 2025 · Small Business Set Aside - Total · Department of the Army, DoD · NAICS 333998 · Solicitation W911S225U2011
Following NAICS 333998? Get new solicitations in it by email as they post — no account needed.
SAM.gov marked this notice inactive — responses were due 16 September 2025.
No award notice on SAM.gov yet. Not every award is posted there, so this does not mean it went unawarded.
Email me when the award is announced. One email, when SAM.gov posts the award notice. Not every award is posted there; if none appears within six months we'll tell you and stop. No account needed.
Can be bid as a nonmanufacturer: 500 or fewer employees, normally sells this item, takes possession of it, and supplies a product made in the US by a small manufacturer unless SBA has waived that. 13 CFR 121.406(b)
This one has closed. We'll email you when new NAICS 333998 (All Other Miscellaneous General Purpose Machinery Manufacturing) solicitations post — the first email lists what is open right now, then at most once a week, only when something new posts. No account needed; unsubscribe in a click.
Description
Waste Water Aerator System MOTOR:HORSEPWER: 14.5-15.5RPM: 1150-1250Full Load AMPS:42/21Voltage 230/460Voltage Phase: 3Cycle: 60Service Factor: 1.15-1.20Insulation Class: ?F? NON-Hygroscopic Bearings:Double Row Angular Contact Bearing Life: 950K-1200K hours Enclosure: Totally Enclose Fan-Cooled Motor (TEFC)MOTORSHAFT: Shaft Material: 17-4 Precipitation-Harding (PH), Stainless steel ( S.S), 1150 Condition Shaft Length: 28inches fromend shield face of motor Shaft Diameter: 1.625 inch O.D Minimum Yield Strength: 135K PSI Maximum Yield Strength: 250KPSIPROPELLER: Material: 316 Stainless Steel Balancing: Dynamically to Less than ? MIL Maximum DEFLECTOR: Material:304 Stainless Steel, HDG Steel and FRP Exterior Finish: CHEM. Resistant GEL-Coat UV Plate Internal Fill: #3 Quartzite andResin Mixture Minimum FRP Thickness: .375 inch Exterior Color: White Weight: 485-490 LBs POWER MODULE SUPPORTRING: Material: 304 Stainless Steel Dimensions of Flat Rings: .5inch by 3inch by 42 inches O.D. Dimensions of support Rod:1.5 inch by 6 inches Method of construction: Welded AERATOR FLOAT: Method of Construction: Hand Lay Up Material: CDM2415 PROMAT and Chemical Resistant Resin External Finish: Chemical Resistant Gel-Coat UV Stabilized External Color:White Internal Reinforcing (Power Module Support) 3/8 in by 3 inch by 42 inches O.D. Steel Ring Internal Reinforcing (MooringEyes): 3/8inch by 3inches by 9 inches Flat Bar Throat Section Reinforcing: 2inch by 2 inch Encapsulated Ribs Internal Fill:2#DEN. Polyurethane Closed Cell Foam Minimum Thickness: .25inch NON-Stress Areas Mooring Eye Dimension 5/8 inchby 3 inch long Float Diameter: 88 inches Float Thickness: 14 inches Sink Safety Factor: 2.5Volute Thickness: FRP .75 inchThick PERFORMANCE: Pumping Rate: 12,172 GPM02 Transfer Rate: 3.0 LBS/HP/HR/Min Minimum DIA. Of Complete Mix at6 feet Depth: 80 Feet Minimum DIA. Of O2 Dispersion at 6feet Depth: 210 Feet WT. Of Completed Unit: estimated 1700 LBSShipping WT Height of Complete Unit: minimum 54 inches/ max 60 inches. Vendor Provide Aerator Dimensions Chart andmanual Mustbe able to deliver on Weekdays 7am to 3 pm
Go deeper on this solicitation
FedSift reads the full solicitation package — every attachment — and pre-extracts the compliance matrix, evaluation factors, key risks, win themes and deal-breakers, each with a verbatim quote and the exact PDF page it came from. It scores the opportunity against your company profile, tells you whether to bid as prime or sub, and ranks teaming partners who could close your gaps.
Source: this notice on SAM.gov. FedSift republishes public federal procurement data and is not affiliated with the U.S. Government. Always confirm dates and requirements against SAM.gov before responding.
